[IMPORTANT] Input Control of Shipping Address Field Read more

KIJIMA

Heizgriff GH08 Druckschalter

Name: Heizgriff GH08 Druckschalter
Brand: KIJIMA
SKU: 21996762
Price: 57.9 EUR
Availability: InStock
Rating: 4.5 (24 reviews)

Product # 304-8206

4.5 (24 Bewertungen)

45.93 ~ EUR (7,933 JPY) 57.9 EUR Save 21%

Webike Point: +79~ pt (0.45 EUR)

Lieferinformationen

Please select product form first.

Menge

Fragen Sie nach diesem Produkt

Kann sie nicht finden? Zitat uns

FITMENT

HONDA

PCX150

KF12 [Frame No.] KF12-1200001 or later *A separate Kijima throttle pipe part number 201-532 is useful for installation.
PCX150

KF12 [Frame No.] KF12-1000001 to 1199999 *A separate Kijima throttle pipe part number 201-532 is useful for installation.
PCX

18- 2BJ-JF81 *A separate Kijima throttle pipe part number 201-5354 is useful for installation.
PCX

14-18 EBJ-JF56 *If Kijima throttle pipe part number 201-5354 is separately available, it will be useful for installation.

Open Fit Model Information Table

Produktbeschreibung unten wird automatisch übersetzen durch Google.

Original zeigen

Product detail

Leistungsaufnahme : 21.2W-36.5W
Druckschalter-Typ

**Dies ist am häufigsten bei Fahrrädern unter 125ccm der Fall, aber wenn Sie es in ein Fahrrad mit geringer Batteriekapazität und Stromerzeugung einbauen, wird es nicht nur nicht warm, sondern die Batterie wird auch leer sein (dasselbe gilt für ausländische Batterien und degradierte Batterien).
*Sie kann nicht für Suzuki-Fahrzeuge mit geringer Leistung und Honda-Fahrzeuge mit weniger als 7S Batterie verwendet werden.
*Es können Batterien vom Typ Yamaha 4B5 oder höher verwendet werden. Selbst wenn es verwendet werden kann, wird das Fahrrad im Leerlauf oder bei niedriger Drehzahl abgeschaltet, wenn die Spannung unter 12 V fällt.
*Je nach den individuellen Eigenschaften Ihres Fahrrads kann es sein, dass es bei voller Leistung nicht genügend Spannung hat und das Fahrrad abgestellt wird..

[Power consumption] 21.2W-36.5W
[Type] Push-switch type

**The stock optional grip heaters manufactured by Honda have a half-wound heating wire, but this product has a full-wound heating wire.The power consumption is higher than that of Honda's optional grip heaters, and starting and using the grip heaters at max heat immediately after engine startup will significantly drain the life of the on-board battery.The life of the battery and electrical system will be extended if the bike is sufficiently ready for startup after the engine has been started, idled, and run 2-3 km.
*Since motorcycles are not power generators, do not use them recklessly. Instead, use the surplus electrical power of the motorcycle gradually. This approach is gentle on the motorcycle.Also, please consider the use of a handlebar cover to increase the overall effect of thermal protection and warmth under low power use.Since the wind blows on your hands and they get cold, if you can physically block the wind, your hands will be less likely to get cold and heat will accumulate.
*With the recent trend toward expansion of electrical components, we have heard from many customers that only the grip heater option is not enough.Motorcycles move by burning fuel, and their explosive power is also used to generate electricity, powering various electrical equipment. Therefore, when considering installation, it is important to first discuss with your bike shop about the essential and preferable options for your bike's electrical accessories. We kindly ask for your careful consideration after consulting with the shop before proceeding with the installation.
*The power demand is so high that even if the system can be used at level 5 of the 5 maximum heat levels when riding on highways or expressways, the battery protection function may automatically stop the power supply when the bike is stopped in traffic jams or at traffic lights.In such a case, please make sure to start up and use it again after reaching cruising speed.
*When installing on a stock or aftermarket throttle tube, it is recommended to warm up the throttle tube before installation to allow for thermal expansion and easier installation.
*Full cowl bikes and scooters may require more labor and may require a longer period of time since the wiring cowl will be threaded during installation.Also, since it is an electrical component, the location for supplying electricity may vary depending on the bike for the optional coupler or surplus wiring. Even if the grip length that can be installed is long, if the wiring work for supplying power is technically difficult and cannot be installed during storage, it could be a problem.Before proceeding, please consult with the bike shop in advance and consider it.
Regarding the corresponding throttle pipe, please thoroughly check the condition of the stock parts and the stock part number. Also, carefully consider that depending on the length of the grip heater, it may not be possible to use stock bar ends.
*In recent times, there has been remarkable progress in motorcycle equipment, and many bikes are now equipped with high-quality components such as heated grips as standard features upon delivery.In this case, please confirm not only this compatibility data but also the actual condition of the bike with the bike dealer.
When installed on bikes with small battery capacity or low charging output, such as those under 125cc, the grip heaters may not only fail to warm up, but they could also cause the battery to drain (this also applies to degraded batteries).
*This product cannot be used for SUZUKI vehicles with low power generation or HONDA vehicles with batteries of less than 7S.
*For YAMAHA, it can be used on the vehicles with 4B5 or higher batteries.Also, even if you can use it, the power supply will be turned off when the motorcycle drops below 12V at idling or low RPM.
*Sometimes, depending on the individual difference of each bike, the power supply is cut off due to insufficient voltage when the bike is turned on to full power.
*Images may contain other products.
*There may be changes in product specifications due to the manufacturer's reasons.
.

5-stufiger Drehschaltertyp.
Der Griffabschnitt ist schlanker als beim Vorgängermodell und reduziert die für die Griffheizung charakteristische Unbequemlichkeit..

Vorsicht

* If there may be an instruction manual included, it will be written in Japanese.

MODEL PAGE LINKS

HONDA

YAMAHA

SUZUKI

Heizgriff GH08 Druckschalter

FITMENT

Product detail

MODEL PAGE LINKS

Delivery Information

NEW ARRIVALS IN USED PARTS FOR

NEW ARRIVALS IN USED PARTS FOR

NEW ARRIVALS IN USED PARTS FOR

New arrivals in used

New arrivals in used

Products ready to ship from stock

Customers who bought this item also bought

Customers who viewed this item also viewed

Beste Sellings für

Beste Sellings für

Beste Sellings für

Best Selling In

Kürzlich angesehene Produkte

Kundenbewertungen

New Custom Articles