Diese Farbe ermöglicht Ihnen die Montage der Schwinge an Ihrer CB750FZ für die Suzuki GSX750S Katana 1100S Katana..
Im Gegensatz zur asymmetrischen CB-F-Schwinge ist die Catana-Schwinge für Links- und Rechtshänder geeignet..
Um dieses Problem zu lösen, werden die linke und rechte Kragenweite geändert und die Catana-Schwingen versetzt montiert..
Sowohl die Radmitte als auch die Kettenlinie sind auf die richtige Position eingestellt, so dass die Serienräder und der Bremsbereich des CB-F angeschraubt werden können..
Der Kragen für die Einstellung der linken und rechten Position des Schwenkarms ist aus Festigkeitsgründen aus Stahl gefertigt und die Oberfläche ist beschichtet, um Rostbildung zu verhindern..
Für die Nadellager werden gehärtete Kragen verwendet..
Räder, Radkränze, Bremssattelstütze und Drehmomentstützen können wie bei den Catana-Schwingen CB750F/CB900F installiert werden..
Schwenkwelle für CB750FZ und Achswelle für CB-F und Katana können verwendet werden..
Die Schwingarm-Schwenkkappe, der Kragen und der Ketteneinsteller im Inneren des Schwenkarms müssen für das Katana vorgesehen sein..
Eine Bedienungsanleitung ist enthalten..
[Bezüglich der Breite des Fangbereichs der Schwingenaufhängung]
Verwenden Sie die Stock Suspensionsbuchsen für CB-F- oder Katana-Buchsen, wenn Sie diese verwenden möchten.. (*siehe Bild 5)
*Es gibt zwei Typen von CB-F Lagerbuchsen, 40548-268-000 (für CB750FZ) und 52451-357-000 (für CB750FA-FC), die beide verwendet werden können..
(Die Breite des Außenumfangs der Buchse ist für CB750FZ (18mm) und CB750FA-FC (16mm), jedoch sind die Breite (19mm), der Innendurchmesser (10mm) und der Außendurchmesser (22mm) der Buchsenmitte für beide Buchsen gleich).
This is a collar which enables to install Suzuki GSX750S Katana 1100S Katana swingarm on CB750FZ.
The Katana swingarm is designed to be used with the asymmetrical CB-F swingarm.
To solve this problem, the width of the left and right collar is changed to offset the Katana swingarm.
Both the wheel center and chain line are correctly positioned to allow bolt-on installation to the stock CB-F wheels and brakes.
The collar to adjust the position of swingarm is made of steel for strength and plated surface to prevent rusting.
In addition, a hardened collar is used for the needle bearing part.
If you change to Katana swingarm, wheel, wheel collar, caliper support and torque rod of CB750F / CB900F can be used.
Pivot shaft is for CB750FZ and axle shaft for CB-F and Katana are both usable.
The cap of the swingarm pivot, the collar inside the pivot and the chain adjuster must be used for Katana.
Comes with an instruction manual.
[About the bushing width of the swingarm suspension support part]
The bushing of the suspension support should be replaced with the stock bushing for CB-F. Or, if you use the bushing for Katana, cut it down to 19mm width.(*See image 5)
*The stock bushing part number for CB-F is 40548-268-000 [for CB750FZ] and 52451-357-000 [for CB750FA-FC], both of them can be used.
(The width of the outer circumference of the bush is for CB750FZ (18mm) and for CB750FA-FC (16mm), but the width (19mm), inner diameter (10mm) and outer diameter (22mm) of the center of the bush are the same for both bushes)